Traffic signals, traffic detectors, CCTV, VMS (portable and permanent) and highway advisory radio (HAR). Also includes speed feedback signs to present drivers with detected speed compared to posted speed limit.
| Functional Object | Description | User Defined |
|---|
| Roadway Advanced Rail Crossing | 'Roadway Advanced Rail Crossing' manages highway traffic at highway–rail intersections (HRIs) where operational requirements demand advanced features (e.g., where rail operational speeds are greater than 80 miles per hour). The active warning systems supported by this application include positive barrier systems which preclude entrance into the intersection when the barriers are activated. This application is activated on notification by wayside interface equipment which detects, or communicates with the approaching train. In this application, additional information about the arriving train is also provided by the wayside interface equipment so that the train's direction of travel, its estimated time of arrival, and the estimated duration of closure may be derived. This enhanced information may be conveyed to the driver prior to, or in context with, warning system activation. This application also includes detection capabilities which enable it to detect an entrapped or otherwise immobilized vehicle on the grade crossing and provide an immediate notification to the wayside interface equipment and traffic management. | False |
|---|
| Roadway Basic Surveillance | 'Roadway Basic Surveillance' monitors traffic conditions using fixed equipment such as loop detectors and CCTV cameras. | False |
|---|
| Roadway Environmental Monitoring | 'Roadway Environmental Monitoring' measures environmental conditions and communicates the collected information back to a center where it can be monitored and analyzed or to other field devices to support communications to vehicles. A broad array of weather and road surface information may be collected. Weather conditions that may be measured include temperature, wind, humidity, precipitation, and visibility. Surface and sub–surface sensors can measure road surface temperature, moisture, icing, salinity, and other metrics. | False |
|---|
| Roadway Field Device Support | 'Roadway Field Device Support' monitors the operational status of field devices and detects and reports fault conditions. Consolidated operational status (device status, configuration, and fault information) are reported for resolution and repair. A local interface is provided to field personnel for local monitoring and diagnostics, supporting field maintenance, upgrade, repair, and replacement of field devices. | False |
|---|
| Roadway Field Management Station Operation | 'Roadway Field Management Station Operation' supports direct communications between field management stations and the local field equipment under their control. | False |
|---|
| Roadway Incident Detection | 'Roadway Incident Detection' provides incident detection using traffic detectors and surveillance equipment. It monitors for unusual traffic conditions that may indicate an incident or processes surveillance images, watching for potential incidents. It provides potential incident information as well as traffic flow and images to the center for processing and presentation to traffic operations personnel. | False |
|---|
| Roadway Passive Monitoring | 'Roadway Passive Monitoring' monitors passing vehicles for a signature that can be used to recognize the same vehicle at different points in the network and measure travel times. Depending on the implementation and the penetration rate of the technology that is monitored, other point traffic measures may also be inferred by monitoring the number of vehicles within range over time. Today this approach is implemented most commonly using a Bluetooth receiver that passively monitors Bluetooth devices on–board passing vehicles and license plate readers that record the vehicle license plate number, but any widely deployed vehicle communications technology or feature that can be passively monitored to uniquely identify a vehicle could be used. | False |
|---|
| Roadway Signal Control | 'Roadway Signal Control' includes the field elements that monitor and control signalized intersections. It includes the traffic signal controllers, detectors, conflict monitors, signal heads, and other ancillary equipment that supports traffic signal control. It also includes field masters, and equipment that supports communications with a central monitoring and/or control system, as applicable. The communications link supports upload and download of signal timings and other parameters and reporting of current intersection status. It represents the field equipment used in all levels of traffic signal control from basic actuated systems that operate on fixed timing plans through adaptive systems. It also supports all signalized intersection configurations, including those that accommodate pedestrians. In advanced, future implementations, environmental data may be monitored and used to support dilemma zone processing and other aspects of signal control that are sensitive to local environmental conditions. | False |
|---|
| Roadway Signal Preemption | 'Roadway Signal Preemption' includes the field elements that receive signal preemption requests from trains, boats (i.e., drawbridge crossings), emergency vehicles, or light rail transit vehicles approaching a signalized intersection and overrides the current operation of the traffic signals to stop conflicting traffic and grant right–of–way to the approaching vehicle. This functional object also services preemption requests received from a TMC to support implementations where the preemption requests are managed by the center. | False |
|---|
| Roadway Standard Rail Crossing | 'Roadway Standard Rail Crossing' manages highway traffic at highway–rail intersections (HRIs) where operational requirements do not dictate advanced features (e.g., where rail operational speeds are less than 80 miles per hour). Either passive (e.g., the crossbuck sign) or active warning systems (e.g., flashing lights and gates) are supported depending on the specific requirements for each intersection. These traditional HRI warning systems may also be augmented with other standard traffic management devices. The warning systems are activated on notification of an approaching train by interfaced wayside equipment. The equipment at the HRI may also be interconnected with adjacent signalized intersections so that local control can be adapted to highway–rail intersection activities. Health monitoring of the HRI equipment and interfaces is performed; detected abnormalities are reported through interfaces to the wayside interface equipment and the Traffic Management Center. | False |
|---|
| Roadway Traffic Information Dissemination | 'Roadway Traffic Information Dissemination' includes field elements that provide information to drivers, including dynamic message signs and highway advisory radios. | False |
|---|
| RSE Situation Monitoring | 'RSE Situation Monitoring' is a general functional object that supports collection of traffic, environmental, and emissions data from passing vehicles. The data is collected, filtered, and forwarded based on parameters provided by the back office. Parameters are provided to passing vehicles that are equipped to collect and send situation data to the infrastructure in snapshots. In addition, this object collects current status information from local field devices including intersection status, sensor data, and signage data, providing complete, configurable monitoring of the situation for the local transportation system in the vicinity of the RSE. | False |
|---|
| RSE Traffic Monitoring | 'RSE Traffic Monitoring' monitors the basic safety messages that are shared between connected vehicles and distills this data into traffic flow measures that can be used to manage the network in combination with or in lieu of traffic data collected by infrastructure–based sensors. As connected vehicle penetration rates increase, the measures provided by this application can expand beyond vehicle speeds that are directly reported by vehicles to include estimated volume, occupancy, and other measures. This object also supports incident detection by monitoring for changes in speed and vehicle control events that indicate a potential incident. | False |
|---|
| RSE Traveler Information Communications | 'RSE Traveler Information Communications' includes field elements that distribute information to vehicles for in–vehicle display. The information may be provided by a center (e.g., variable information on traffic and road conditions in the vicinity of the field equipment) or it may be determined and output locally (e.g., static sign information and signal phase and timing information). This includes the interface to the center or field equipment that controls the information distribution and the short range communications equipment that provides information to passing vehicles. | False |
|---|
| Document Number | Title | Description |
|---|
| CTI 4001 | Roadside Unit (RSU) Standard | This document establishes a non–proprietary, communications–agnostic, industry consensus Roadside Unit (RSU) Standard. An RSU is a transportation infrastructure communications device that is a part of a Cooperative Intelligent Transportation Systems (C–ITS) transportation environment. The goal of such an environment is to reduce the number of fatalities and injuries on roadways, improve mobility, and reduce environmental impacts of transportation systems. Commonly known as the Connected Vehicle (CV) environment in the United States (US), it includes both connected human–driven vehicles and connected automated vehicles (CAVs). The terms Vehicle–to–Infrastructure (V2I) and Vehicle–to–Vehicle (V2V) are used to reflect the exchanges of messages within the CV environment. The vision for this technology has expanded to include all types of travelers including pedestrians, cyclists, multimodal travelers, and other vulnerable road users (VRUs), and is referred to as Vehicle–to–Everything (V2X) technology and V2X communications. |
|---|
| ITE ATC 5201 | Advanced Transportation Controller | This standard defines the functionality and performance requirements for a modern ITS controller known as an ATC. It is similar to the NEMA TS–2 standard in that it defines basic capabilities but leaves hardware choices up to the manufacturer. |
|---|
| ITE ATC 5202 | Model 2070 Controller Standard | This standard specifies the hardware for a modern, open–architecture controller for ITS applications that can run Linux and is capable of executing advanced signal controller logic, among other things. |
|---|
| ITE ATC 5301 | Intelligent Transportation System Standard Specification for Roadside Cabinets | This standard specifies the characteristics of a modern controller cabinet for the ITS industry. |
|---|
| ITE ATC 5401 | Application Programming Interface Standard for the Advanced Transportation Controller | This standard defines the application programmers' interface (API) that should be supported by an ATC, which is an open–architecture controller that can host multiple ITS applications. |
|---|
| NEMA TS 8 | Cyber and Physical Security for Intelligent Transportation Systems | This specification describes how agencies and other transportation infrastructure owner/operators should implement cyber– and physical–security for ITS. |
|---|
| NEMA TS2 | Traffic Controller Assemblies with NTCIP Requirements | This specification covers traffic signaling equipment used to facilitate and expedite the safe movement of pedestrians and vehicular traffic. |
|---|
| NEMA TS4 | Hardware Standards for Dynamic Message Signs (DMS) With NTCIP Requirements | This standard provides hardware specifications for safe, dependable, functional, and easily maintained Dynamic Message Sign (DMS) equipment. |
|---|